Life Racing F88RS ECU

In stock
SKU: ECU-A03
Regular price £1,971.00
Build Options
Engine Upgrades
Driveline & Security Upgrades
Product details
  • SKU ECU-A03
  • Model F88RS ECU
  • Make Life Racing

Do you have questions about this product?

Ask an expert!

Life Racing F88RS ECU – Professional Engine Management

The Life Racing F88RS ECU is part of Life Racing's F88R family (F88R, F88RS and F88RX). All share the same RISC CPU and custom synchronous FPGA, tracking engine position up to 25,000rpm, and differ in injector/PWM output count and logging memory. The F88RS has 12 PWM / injector outputs and 32MB logging.

Choose extra ignition outputs, a second lambda or third CAN bus and extra frequency inputs as Build Time Choices with the options above, and add software upgrade features such as traction or gearbox control.

Key features

  • Ignition: 4 outputs (IGBT or TTL, software configurable) as standard, 6 with the Build Time Choice.
  • 12 general PWM / injector outputs.
  • 2 full H-bridges (or 4 half-bridges / 4 PWMs) for drive-by-wire.
  • 24 analogue inputs, including bipolar, inductive or Hall effect speed/position inputs (up to 8 with the 8 Frequency BTC).
  • Optional 2 acoustic knock inputs and up to 2 NTK wideband lambda interfaces.
  • 32MB logging, battery-backed and time/date stamped, with 100MHz Ethernet download.
  • 2 x CAN 2.0B (3 with BTC) and RS232.

Hardware

Sealed, high-pressure die-cast black powder-coated aluminium case, 88-way Bosch/AMP sealed connector, 2 individually protected 5V sensor supplies and 5 separately protected grounds. 480g, rated to +85°C.

Build Time Choices (select under 'Build Options' above)

Build Time Choices are hardware options fitted when the ECU is built. They cannot be added later, so choose them with the ECU.

Option What it does Price
6 Ignition Outputs (ECU-BTC-6I) Adds 2 ignition outputs (4 to 6) for six-cylinder coil-on-plug, or to drive idle valves / VVT solenoids. +£145
Second Lambda (ECU-BTC-2L) Adds a second NTK wideband interface for per-bank fuelling trim. +£285
3rd CAN Bus (ECU-BTC-3C) Adds a third CAN 2.0B bus in place of the second lambda interface. +£285
8 Frequency Inputs (ECU-BTC-8F) Increases bipolar / inductive / Hall effect speed inputs to 8 for wheel speeds, cam and turbo speed. +£215

Optional Software Upgrades (select above)

Choose any software upgrades from the upgrade drop-downs above and they will be enabled before dispatch. To add a feature to an ECU you already own, contact us first.

Upgrade What it does Drop-down Price
Adaptive Knock Control (ECU-FEAT-K) Uses up to 2 knock sensors and retards ignition only on knocking cylinders, then reintroduces timing in steps. Requires 720° sync. Engine Upgrades +£285
Wastegate Position Control (ECU-FEAT-W) Closed-loop wastegate position control integrated into boost control. Engine Upgrades +£191
Direct Motor Control (ECU-FEAT-E) Access to the H-bridge pins for up to two drive-by-wire motors, or low-side / half- / full-bridge drives. Engine Upgrades +£285
Traction Control (ECU-FEAT-T) Up to 4 conditioned wheel speed sensors with spin target, gain, fuel/ignition cut and map select; can also use yaw, lateral G or steering angle. Driveline & Security Upgrades +£285
Gearbox Control (ECU-FEAT-G) Sequential gearbox control: gear ratio learning, gear cut, gear blip and over-rev protection. Driveline & Security Upgrades +£407
Custom ID Creation (Custom Security) (ECU-ID-XXX) One of Life Racing's Custom Security options. Contact us to discuss set-up. Driveline & Security Upgrades +£342
Security Dongle (Custom Security) (ECU-DNG-XXX) Physical security dongle, one of Life Racing's Custom Security options. Contact us to discuss set-up. Driveline & Security Upgrades +£174

Technical Specifications

Feature Specification
Max tracking speed 25,000rpm
Ignition outputs 4 (6 with BTC)
PWM / injector outputs 12
Full H-bridges 2
Analogue inputs 24
Lambda 1 (2 with BTC)
Logging 32MB internal
Comms 100MHz Ethernet, 2x CAN 2.0B (3 with BTC), RS232
Supply voltage 6–32V, reverse polarity protected
Connector 88-way Bosch/AMP sealed (kit CON-B01 sold separately)
Dimensions 183 x 125 x 36mm inc. connector
Mass 480g

FOR MAPPING / CALIBRATION SERVICES FOR THIS ECU PLEASE CONTACT US